![]() Specifications • Warranty: Sand Filter motor - 12 Months • Warranty: Sand Filter Casing - 12Months • Warranty: Control Valve - 12 Months • Warranty: Handle - 12 Months • Warranty: Hoses and Accessories - 1 Month • Requires: Size 20 silica sand. 0.45 - 0.85mm Item No. 58271 Pump Flow Rate 2,006 l/h (530g/h) System flow Rate 2,006 l/h (530g/h) Certification 220-240v~50Hz, 90W Weight CE/EMC Rating 7.4kg (16.3lb) Item No. 58257 Pump Flow Rate 3,785 l/h (1,000g/h) System Flow Rate 3,785 l/h (1,000g/h) Certification 220-240v~50Hz, 90W Weight 12.2kg (26.8lb) Rating CE/EMC Item No. 58199 Pump Flow Rate 5,678 l/h (1,500g/h) System Flow Rate 5299 l/h (1,400g/h) Certification 220-240v~50Hz, 90W Weight 14.3kg (31.5lb) Rating CE/EMC Item No. 58286 Pump Flow Rate 4,542 l/h (1,200g/h) System Flow Rate 4,164 l/h (1,200g/h) Certification 220-240v~50Hz, 90W Weight 15.2kg (33.5lb) Rating CE/EMC Item No. 58315 Pump Flow Rate 7,571 l/h (2000g/h) System Flow Rate 6,814 l/h (1800 g/h) Certification 220-240v~50Hz, 90W Weight 14.9kg (32.9g/h) Rating CE/EMC. Reasons Solutions Sand is too small Recommended 0.45mm to 0.85mm #20 Silica Sand Moved the control valve and performed the back flush to the filter function without stopping the sand filter Stop the sand filter before setting the control valve The skimmer is broken Replace the skimmer The level of the sand is too high Check the level of the sand is between the marks MAX and MIN on the hub (4-5cm under the top of the tank) No back flush and rinsing has been performed Perform the back flush and rinsing procedure, especially when the sand is new. Soul assassins intermission rar download torrent. Reasons Solutions The ozone generator has reached its life span Go through checklist guide, if this does not resolve the problem, the pump will need replacing. Replacements can be purchased from or Control valve is not set to filter function Set the control valve to filter function Hoses are broken and there is no water flow >Replace the hoses. Replacements can be purchased from or No water flow Go through checklist guide, if this does not resolve the problem, the pump will need replacing. Replacements can be purchased from or Dirty filter Perform the back flush procedure. If the pressure reading on the pressure gauge is 0.045 MP (6.5 PSI) or higher or the water flow to the pool is too low it could be the time to clean the sand. ![]() Please check the following: If there is any blockages in the hoses If the connection valves are closed or partially closed After having checked the above conditions, please follow the instructions on the manual to perform backwash and rinsing. J supranto statistik teori dan aplikasi pdf. If after having performed them, there is still a high-pressure reading, sand bed replacement is necessary. Just purchased a Bestway 18x9x48 above ground pool from costco with a sand filter this past weekend. I followed all the backwash and rinsing instructions. When the Control valve is set to circulate the pressure is at 6ps with a good amount of flow going to the pool. When the control valve is set to filter the pressure is 1psi or less and the flow is very low. I removed all the sand and cleaned the Screen then reassemble without adding any sand. The psi is still low and so is the flow. Does anyone have any suggestions what I should do? Thank you, Daniel.
0 Comments
Leave a Reply. |